Ming RenBroker · RE/MAX Realtron Realty Inc., Brokerage
☎ 647-779-9186

Buying a Home

Why Don't the Square Footage Numbers Match? MPAC and MLS Measure Differently

By , Broker, RE/MAX Realtron Realty Inc. (About Ming) · Published

Ming Ren · Broker · RE/MAX Realtron Realty Inc., Brokerage

← All articles · Buying a Home · Category guide

I am Ming Ren, a Broker with RE/MAX Realtron.

The plain conclusion: for one home you will see at least three area figures — MPAC's record, the MLS listing, and what you measure inside — and a mismatch usually means different measuring methods, not bad faith. MPAC measures above-grade floors from the outside of the exterior walls. The usable interior area is naturally smaller. Separate the methods first; only then does price per square foot mean anything.

First: MPAC measures the outside, and only what is above grade

MPAC (Municipal Property Assessment Corporation) records a home's area using exterior measurements of the above-grade floors, wall thickness included, because it needs one consistent basis for valuing every property in Ontario for tax purposes. It is not a furniture-planning number, so an MPAC figure that is larger than your interior measurement is expected, not an error.

What it leaves out matters just as much: basements are excluded from above-grade area, even a fully finished walk-out basement, and attached garages are excluded too. A home recorded at 1,800 square feet may offer far more usable space once a finished basement is counted. Judging size from one total misprices exactly those homes.

Second: the MLS figure can come from four different sources

The area on an MLS listing is not guaranteed to be MPAC's. It may come from MPAC records, the listing agent's own measurement, builder plans, or the seller, and the system does not verify each figure. Condos show the widest gaps: builder plan areas may include exterior walls and sometimes a share of common elements, so the interior area at occupancy can come in noticeably smaller — the question pre-construction buyers ask me most.

My practice: whenever area drives the decision — price per square foot, rental projections, comparing floor plans — confirm the stated source first, cross-check against the MPAC record, and for a material purchase have the interior measured properly. Compare like with like, or do not compare at all.

Condos need one more layer of separation: whether a balcony, locker or parking space is counted in the marketed area varies by project — some count a balcony in full, some at half, some not at all. Within one building, the "area difference" between a large-terrace suite and a standard suite may be mostly terrace, not interior space. When comparing two suites, pull the net interior area out and compare that on its own, and value semi-outdoor space separately, rather than running one total through a single yardstick.

Third: MPAC records can be corrected, but there is a deadline

Every owner can view their property's recorded details — area, age, room counts and assessed value — free on MPAC's AboutMyProperty. If the data or the value looks wrong, the first step is a Request for Reconsideration (RfR) to MPAC. Under section 39.1 of the Assessment Act, the general deadline is March 31 of the taxation year; supplementary or omitted assessment notices carry their own deadline shown on the notice. For residential properties, the RfR usually comes first; if you disagree with MPAC's result, an appeal to the Assessment Review Board (ARB) follows within 90 days of that result.

Watch for one passive change as well: additions, extensions or a basement renovation you do after buying will reach MPAC through municipal permit records, and the recorded area and assessed value may be updated, followed by a supplementary assessment notice and a supplementary tax bill. That is not an MPAC error — the record has caught up with the house. Price that future cost in before you renovate, especially if the new space will become a rental unit, where assessment and tax treatment can both shift.

Note the distinction: wrong data (an overstated area, for example) is corrected with evidence about the property itself, while a value dispute is argued with comparable assessments and sales. They are different conversations with different materials.

An invented example, with made-up numbers, to show how method alone can flip a conclusion: two detached homes in one area — Home A listed at 2,400 square feet asking $1,200,000, Home B at 2,100 square feet asking $1,120,000. Roughly, A looks cheaper per foot at $500 versus about $533. But A's figure came from builder-plan measurement and B's from MPAC. Align both to the MPAC record — A at 2,150, B at 2,100 — and the unit prices reverse to about $558 for A and $533 for B. Layout, condition and lot are still unexamined; the measuring basis alone was enough to mislead the comparison.

Three common misunderstandings

"MPAC's area is bigger than mine, so the government made an error." Usually not. Exterior measurement including walls versus your interior dimensions explains the gap. Compare methods before claiming a mistake.

"A finished basement should count when I compare price per square foot." In MPAC's method it does not form part of above-grade area. You can absolutely value the basement in the total price — but keep the numerator and denominator on the same basis or the per-foot figure is meaningless.

"If the record is wrong, MPAC will fix it any time." The RfR has a hard deadline — generally March 31 of the taxation year. Miss it and you wait for the next year, so note the date when you buy.

When viewing or buying, I suggest this order

  1. Ask where the listing area came from: MPAC, agent measurement, builder plans or the seller.
  2. Pull the MPAC record on AboutMyProperty and set it beside the listing figure.
  3. If area drives your offer, have the interior measured and compare candidates on one basis only.
  4. On pre-construction, ask the builder to state the plan-area method and the net interior area.
  5. If the MPAC record is wrong, file the RfR before the March 31 deadline, with data errors and value arguments kept separate.

Ming Ren, Broker, RE/MAX Realtron


This article is general information, not legal advice. Individual assessment records and deadlines affect the outcome; consult an Ontario lawyer or assessment professional before acting.

Primary sources: MPAC official guidance (mpac.ca / AboutMyProperty) on property data and assessment; Assessment Act, R.S.O. 1990, c. A.31, s. 39.1 on Request for Reconsideration deadlines (Ontario e-Laws, checked November 2026).

Frequently asked questions

MPAC's area is bigger than mine, so did the government make an error?

Usually not. Exterior measurement including walls versus your interior dimensions explains the gap, so compare methods before claiming a mistake.

Should a finished basement count when I compare price per square foot?

In MPAC's method it does not form part of above-grade area. You can value the basement in the total price, but keep the numerator and denominator on the same basis or the per-foot figure is meaningless.

If the record is wrong, will MPAC fix it any time?

The RfR has a hard deadline, generally March 31 of the taxation year. Miss it and you wait for the next year, so note the date when you buy.

This article in other languages: 中文فارسی

Want to talk about your home?

You can also call directly, or scan the code to add Ming on WeChat.

Ming’s WeChat QR code
Scan to add on WeChat

Community guides by city

All cities →
☎ Call MingFree Evaluation