Ming RenBroker · RE/MAX Realtron Realty Inc., Brokerage
☎ 647-779-9186

Living & Communities

Is Spray Foam Worth It in Ontario? Check the Installer and the Re-Occupancy Plan First

By , Broker, RE/MAX Realtron Realty Inc. (About Ming) · Published

Ming Ren · Broker · RE/MAX Realtron Realty Inc., Brokerage

← All articles · Living & Communities · Category guide

I am Ming Ren, a Broker with RE/MAX Realtron.

Here is the plain conclusion: spray foam can be worth it. It insulates well and seals air leaks. But it is not like paint or batts. The material is created in your home, on the day, by mixing two chemicals, spraying them, and letting them cure. Done right, it is uneventful afterwards. Done with the wrong ratio, temperature, or ventilation, it can leave odour and a repair that is hard to undo. Before you compare price per inch, settle three things: who installs it, when you can move back in, and what covers the foam.

First: open-cell and closed-cell are different tools

Both are spray polyurethane foam, but density and use differ, and so does price. Do not choose on R-value alone.

Type General character More common use Watch out for
Open-cell (low density) Softer, more vapour-permeable, lower insulation value per thickness, usually lower cost Interior walls, locations where sound control also matters Do not count on it as a moisture barrier in a damp location
Closed-cell (medium density) Rigid, higher insulation value per thickness; at the thickness its product listing requires, it can also help with air and moisture control Basement walls, tight roof or wall cavities, locations where moisture control matters Costs more; water that gets behind it does not drain easily, and the problem is harder to see

An illustrative example only, invented to show the arithmetic, not a quote: suppose a wall needs about R-20. Open-cell would need noticeably more thickness to get there, while closed-cell might get there thinner. If the cavity is shallow, that difference matters. If the cavity is deep and the job is an interior partition for sound, the extra money for closed-cell may buy you very little. Start with the location, the available depth, and where moisture comes from, then look at budget.

One selling point to keep in mind: once foam covers framing, wiring, and pipes, a future buyer or home inspector will have a harder time checking structure and past leaks. Photograph the assemblies before they are sprayed. That helps you with repairs, and it helps you explain the work when you sell.

Second: the real risk is on spray day, not years later

Health Canada has a specific page on MDI substances. It says two-component spray foam products may cause breathing problems and skin sensitivities, and it advises following product instructions, ventilating, and using proper protection. Canada has also published a code of practice for low-pressure two-component spray polyurethane foam products, aimed at reducing exposure to MDIs. In renovation language: the highest-exposure window is during spraying and the early curing and ventilation period, not years later.

A proper job therefore does not skip a few basics. Occupants, children, and pets leave the work area. The crew wears protection. The space is ventilated. And the re-occupancy time is agreed before work starts. That time is not one universal number for every product. It depends on the specific product, the thickness applied, ventilation, and the manufacturer's direction. If someone promises you can stay in the house the whole time and move straight back in with no plan, ask more questions. Properly cured and ventilated foam should see odour fade. If odour persists or gets stronger after you return, or someone develops breathing irritation, do not just endure it. Ventilate, leave that area, and use the product and installation records to get the installer and appropriate professionals involved.

This is why installation matters so much here. The foam is manufactured on site. An off-ratio mix, a damp substrate, or the wrong temperature can leave foam that does not cure fully. Removal and redoing it is usually the last resort, and it is disruptive and expensive. Getting it right once matters more than fixing it later.

Third: in Canada, check the standard, the certified installer, and the covering

For medium-density closed-cell foam, Canada has a clear standards chain. Evaluations from the Canadian Construction Materials Centre (CCMC) of the National Research Council cite CAN/ULC-S705.1 for the material and CAN/ULC-S705.2 for on-site application. The product is to be used under its CCMC listing conditions, and it must be installed only by installers certified under the designated site quality assurance program, holding valid photo identification they can show on request. Low-density open-cell products sit under the corresponding CAN/ULC-S712 series and their own evaluation conditions. Either way, put the full product name and evaluation number in the contract. A line that just says “spray foam” is not enough.

Do not skip the fire-protection layer either. Where foamed plastic faces interior space, building code generally requires a protective covering that separates it from fire for a period of time. A common finish is about 12.7 mm (half-inch) gypsum board. In attics, crawl spaces, and other limited-access areas, the product evaluation or the local building department may allow a different protective approach. What applies to your wall is a question for the current Ontario Building Code, the product's CCMC conditions, and your municipal building department. Do not leave foam exposed in living space long term, and do not accept “everyone does it this way” as a substitute for checking.

On rebates, I will say only what is safe to say: these programs change often. Older federal Greener Homes arrangements have ended or changed. In Ontario, the current insulation-related path is the Home Renovation Savings program, delivered with Enbridge Gas and Save on Energy. Its official pages list insulation as a category, but the amount, whether a home energy assessment is required first, and whether a participating contractor is required all depend on which upgrade you do and when you apply. Check the current official terms before you sign. Do not budget using an old program's amount, and do not treat a rebate you have not been approved for as money already saved.

Three common misunderstandings

Misunderstanding one: “Closed-cell has the higher R-value, so use it everywhere.” No. In a deep interior wall where sound is the point, open-cell may already do the job. Extra money is only worth it when it buys something real: saved thickness, or moisture control you actually need.

Misunderstanding two: “The foam comes ready-made from a factory, so any installer is the same.” It is the opposite. It is mixed and made on site in your house. A CCMC-listed product still needs a certified installer under the right standard and a site quality assurance program. You need both.

Misunderstanding three: “If there is no smell, we can move right back in.” Re-occupancy timing should follow the manufacturer's time for that product, the thickness, and the ventilation, and it should be set before work begins. Lack of smell is only one observation. It does not replace the manufacturer's and installer's re-occupancy direction, and households with asthma, young children, or older adults should leave extra margin.

If you are about to sign a spray foam contract, do it in this order

  1. Fix water first. Track down and repair roof, basement, or exterior-wall leaks and chronic damp before you spray. Do not expect foam to seal a water problem shut.
  2. Make the quote name the product in full, open-cell or closed-cell, the target thickness, the CCMC evaluation number, and the material and application standards. Do not accept only a total price and an area.
  3. Check the installer's certification in person, confirm it is current, and ask which site quality assurance program covers the job. If the credential does not match the product, choose someone else.
  4. Agree the departure and re-occupancy plan before work starts: who leaves, for how long, how the space will be ventilated, and what re-occupancy time the manufacturer gives. Put it in the contract or work order.
  5. Ask who installs the protective covering over the foam, what it is, and when it will be finished. Confirm with your municipal building department whether your project needs a permit and inspection.
  6. Check rebates last, and check them live: confirm eligibility and process on the official Home Renovation Savings pages under the terms in effect now. If an assessment or registration must come first, do it before work starts, not after.
  7. Photograph framing, pipes, and wiring before spraying, and keep written records of the product, thickness, installation date, and re-occupancy direction. You will want them for repairs and for a future sale.

Honest work, done properly, step by step. I am Ming Ren. If you are considering insulation work at home, bring the product sheet, the installer's credential, and the re-occupancy plan, and we will go through the locations and the numbers one by one before anyone compares unit prices.


This article is general information only, not building, health, or legal advice. Product suitability, code requirements, and rebate eligibility depend on the manufacturer's instructions, CCMC evaluation conditions, the current Ontario Building Code, and official program terms. Consult a qualified installer and your local building department before work, and seek medical care promptly for breathing symptoms or other health concerns.

Primary sources: Health Canada, MDI substances page and Code of Practice for low-pressure two-component spray polyurethane foam products (Canada.ca); NRC-CCMC product evaluations citing CAN/ULC-S705.1 (material) and CAN/ULC-S705.2 (application), certified installers and site quality assurance; Natural Resources Canada, Keeping the Heat In; Home Renovation Savings official program pages (Enbridge Gas / Save on Energy), all checked November 2026. The R-20 figure above is an illustrative example, not a real quote or a conclusion about any specific home.

Frequently asked questions

Closed-cell has the higher R-value, so should it be used everywhere?

No. In a deep interior wall where sound is the point, open-cell may already do the job; extra money is only worth it when it buys saved thickness or moisture control you actually need.

Does the installer matter if the foam product is the same?

Yes. The foam is mixed and made on site in your house, so a CCMC-listed product still needs a certified installer under the right standard and a site quality assurance program.

If there is no smell after spraying, can we move right back in?

No. Re-occupancy timing should follow the manufacturer's time for that product, the thickness, and the ventilation, and be set before work begins; lack of smell does not replace that direction.

This article in other languages: 中文فارسی

Want to talk about your home?

You can also call directly, or scan the code to add Ming on WeChat.

Ming’s WeChat QR code
Scan to add on WeChat

Community guides by city

All cities →
☎ Call MingFree Evaluation