I am Ming Ren, a Broker with RE/MAX Realtron.
The plain conclusion first: in Ontario, the boiler and pressure vessels in a commercial building are not ordinary building equipment. They are regulated devices, overseen by TSSA (the Technical Standards and Safety Authority) under the Technical Standards and Safety Act, 2000 and O. Reg. 220/01. A regulated device may not legally operate without a current Certificate of Inspection (COI). And the point owners most often miss is this: if the device carries boiler and machinery insurance, its periodic inspection is normally performed by the insurer's authorized inspection agency and reported so the COI can be renewed. Your legal permission to run the boiler rides on a policy you may think of as a purely financial product. Let the policy lapse, change insurers without a clean handover, or let the equipment schedule drift — and the certificate can quietly expire while the boiler keeps firing.
Three things follow: which devices are regulated, the paper chain that lets one run legally, and where the inspection–insurance link breaks.
1. First question: is the device regulated? Do not judge by water temperature
O. Reg. 220/01, section 2, draws the boundary by exclusion, and boilers and pressure vessels are tested differently.
A pressure vessel is regulated where its maximum allowable working pressure exceeds 103 kPa (15 psi). A vessel, fitting or piping at or below that pressure is expressly excluded. A boiler is regulated by default, and the exemptions are narrow: a hot liquid heating system circulating freely to an atmospheric expansion tank with no valves or obstructions in between; a low pressure boiler with a wetted heating surface of 30 square feet (2.79 m²) or less, or a power rating of 30 kW or less; and any boiler with a heating surface of 10 square feet (0.93 m²) or less.
The common error is using low water temperature to write a boiler out of the regime. The regulation's lines are heating surface and power rating, not outlet temperature. A commercial hot water boiler of any real size clears those narrow exemptions and is regulated. On a purchase, the first move is not "does it have a boiler?" — it is reading the nameplate data of each device against those lines.
| Device | Line for being regulated | Common misjudgment |
|---|---|---|
| Pressure vessel, fitting, piping | Maximum allowable working pressure over 103 kPa (15 psi) | Assuming every tank is regulated — or none is |
| Low pressure boiler | Exempt only within the narrow 30 sq ft / 30 kW limits | Inferring exemption from low water temperature |
| Boiler generally | Exempt only at a heating surface of 10 sq ft or less; otherwise regulated by default | Judging by age or condition instead of nameplate data |
2. Legal operation rests on a paper chain
A regulated device is traceable from design onward. Its design must be registered with TSSA against the applicable North American code, which produces a Canadian Registration Number (CRN) marked on the nameplate — the device's proof of identity. After installation, an installation inspection is performed and, on passing, a COI is issued before the device goes into service.
The COI is not one-and-done. The device is subject to periodic inspection for its entire operating life, at the intervals set for its type, and each passed inspection keeps the certificate current. Operating a boiler or pressure vessel without a current COI is itself a violation, and it colours insurance and liability if anything goes wrong. So due diligence should ask for the whole file — nameplate CRN, installation inspection record, a continuous run of COIs, and any outstanding orders — not a verbal "the boiler is fine."
3. Why the periodic inspector often works for your insurer
This is the most counterintuitive part of the system, and the place where things actually break. Under section 10 of O. Reg. 220/01, periodic inspection runs on two tracks. If the device is not insured, an inspector inspects it at the intervals set out in the code adoption document and the owner pays the inspection fee. If the device is insured under boiler and machinery insurance, the periodic inspection is carried out by the insurer's authorized inspection agency and reported to the regulator, and the COI is renewed on that basis.
In other words, who knocks on your door to inspect depends on your insurance. The failures happen at the handover points: a sale closes and the insurer changes; a policy renews with an equipment schedule that no longer matches the boiler room; the owner assumes inspections are "the government's job" while the broker assumes TSSA will simply show up. At every one of those gaps, the boiler does not stop — the certificate expires. Discovering a lapsed COI at the next inspection, a claim, or an incident investigation is a very different problem from renewing one on time.
One more bottom line: incidents involving a boiler or pressure vessel carry reporting duties under the regulation. Do not repair first and report later. Preserve the scene, report through the current TSSA channel, and then deal with the equipment.
Three common misunderstandings
"The water temperature is low, so TSSA cannot be involved." The lines are heating surface and power rating, not temperature. Most commercial boilers clear them. Treat the device as regulated and verify device by device against the nameplate.
"Inspection is the government's job — they will come when it is due." For an insured device, the periodic inspection normally runs through the insurer's inspection agency. If nobody comes, the likely cause is a break in your own insurance handover, not an exemption from inspection.
"The certificate expired a few days ago — keep firing and fix it later." Operating a regulated device without a current COI is itself non-compliant. Stop, get the inspection done and the certificate restored, and then resume. Do not gamble that nothing happens in the gap.
If you are buying, or already own, a building with a boiler, do these five things in order
- Record every nameplate: device type, CRN, maximum allowable working pressure, heating surface or power rating — and test each device against O. Reg. 220/01.
- Ask for the complete paper chain: installation inspection record and the full run of COIs, and check that the certificate is current with no gaps in the history.
- Confirm in writing with your insurance broker: boiler and machinery coverage is in force, the insured equipment schedule matches what is actually in the boiler room, who arranges the periodic inspection, and whether the last inspection report was filed.
- Put the inspection expiry date in the property management calendar and book the next inspection ahead of it — not after the certificate lapses.
- In a transaction, put COI status and document handover on the due diligence list. If a device's status is unclear, have an engineer or lawyer familiar with the TSSA regime confirm it rather than guessing from experience.
Trust Professional, Diligent Work. I am Ming Ren. When you tour a commercial building, do not skip the boiler room — verify the certificate and the insurance link first, and we will go through the file item by item.
This article is general information only, not legal or engineering advice. A specific device's status, inspection interval and operator requirements are governed by O. Reg. 220/01, the applicable code adoption document and current TSSA requirements. Consult an Ontario lawyer or a qualified engineering professional before acting.
Primary sources: Technical Standards and Safety Act, 2000; O. Reg. 220/01, ss.1, 2, 8–10 (Ontario e-Laws); TSSA Boilers and Pressure Vessels Safety Program guidance (consulted November 2026).


