I am Ming Ren, a Broker with RE/MAX Realtron.
The conclusion first: in Toronto, pool water has two dependable routes — into the sanitary sewer connection on your own property, or discharged in a controlled way onto your own lot, staying within your boundary until it evaporates or soaks into the ground. Running a hose to the curb is the easiest way to get it wrong. A regular chlorine pool may use the storm sewer only if five conditions are all met at once, and a salt water pool has no storm sewer route at all.
The rules sit in Chapter 681 (Sewers) of the Toronto Municipal Code. Before you start the pump, sort out three things: what kind of pool you have, which system the water is entering, and whether the water can reach a neighbour's lot.
First: the two pool types have different routes
Chapter 681 addresses private residential pools — pools, hot tubs, spas or wading pools serving five or fewer single-family residences, which covers the typical detached-house backyard. Anything larger falls outside that definition.
Regular (non-salt) pools are dealt with in s.681-11T. The section prohibits discharge except by two permitted methods: a temporary connection to the sanitary sewer, or controlled discharge on your own lot that stays on the lot until it evaporates or infiltrates. Beyond those two, there is one conditional exception — the storm sewer, covered below.
Salt water pools are dealt with in s.681-11U, and only those two methods are listed: the sanitary connection on your own property, or controlled discharge on your own lot that does not migrate to neighbouring land. There is no storm sewer option in that section. That makes sense: waiting and dechlorination do not remove salt, and storm sewers lead toward waterways.
So step one is not testing the water. It is identifying your system. And note that the grate at the curb normally connects to the storm system, not the sanitary sewer. If you are unsure how the lines near your home run, call the City at 311 rather than copying a neighbour.
Second: the storm sewer needs all five conditions
Under s.681-11T(3), a regular pool may discharge to the storm sewer only when all of the following are met: there are no algaecides in the water; the water has been held in the pool for one week after the last dose of chlorine and the chlorine concentration in the wastewater is at or below 0.01 mg/L; the water is treated with sodium sulphite to achieve that total chlorine limit; the copper concentration is at or below 0.04 mg/L; and the owner complies with the City's Environmental Best Management Practices for swimming pools, with Chapter 681 prevailing if the two conflict.
Note that holding the water for a week and treating it with sodium sulphite are two separate conditions, not alternatives. The City's pool-draining page gives the same storm limits: chlorine at or below 0.01 mg/L and copper at or below 0.04 mg/L, with dechlorination first.
Honestly, the hard part of this route is not doing it — it is proving it later. How many days the water sat, what the tests showed, and what treatment was used all need records. If you cannot document each step, the sanitary and on-lot routes carry far fewer preconditions. For how your own plumbing connects, ask a licensed plumber or call 311.
Two related flows are different again. Filter backwash water under s.681-11W must go to the sanitary sewer or your own lot, must not reach the street or a neighbour's lot, and has no storm sewer exception. Rainwater collected on a pool cover may go to the storm sewer under s.681-11V, but still must not be discharged near a ravine in a way that erodes slopes or harms trees and vegetation.
Third: keeping it on your own lot still has hard boundaries
Discharging on your own property sounds simplest, but the bylaw draws two firm lines. The water must stay within your lot until it evaporates or infiltrates, and discharge in a manner that causes or may cause it to flow onto an adjacent property is prohibited — "may cause" is enough; the neighbour's yard does not have to actually flood. Discharge over a ravine or valley slope that causes or may cause erosion or instability is also prohibited, which matters for ravine lots.
Now apply that to the most common shortcut: a pump hose run down the driveway toward the street. If the water spreads onto the neighbour's lot on the way, the on-lot rule is already breached; if it ends in the curb grate, the five storm conditions apply on top. One convenient route can fail in two places.
The penalties in s.681-14.1 are maximum fines on conviction, not the amount on any particular ticket: up to $50,000 for an individual first offence and $75,000 for a subsequent one, up to $100,000 for a corporation, with additional daily fines for a continuing offence. Actual enforcement is not stated in the chapter, and I will not guess at it. Landlords should also note that the duty sits with the owner; tenants and service contractors are the means by which the owner complies, not a transfer of the duty.
Common misunderstandings
Myth 1: “My neighbour drains to the street, so I can too.” A neighbour's habit is not authority. Their pool may be a treated chlorine pool — or they may simply not have been caught. Confirm your own pool type and water quality.
Myth 2: “The water looks clear, so the chlorine must be gone.” Clear is not compliant. The storm route turns on numbers — chlorine at or below 0.01 mg/L and copper at or below 0.04 mg/L — which require testing, not eyesight.
Myth 3: “If I let a salt water pool sit long enough, it can go to the storm sewer.” No. The salt water section lists only the sanitary sewer and your own lot. Sitting does not remove salt, and the exception never applied to salt pools.
Myth 4: “Water on my own lot can't be a problem.” It depends where it ends up. Flowing onto a neighbour's land or over a ravine slope is prohibited, and the responsibility does not shrink because the pump was on your side of the fence.
Before you drain, work through this order
- Confirm whether your pool is a salt water or regular chlorine system; if it is salt, rule out the storm sewer and choose between the sanitary connection and your own lot.
- Confirm whether your intended outlet connects to the sanitary or the storm system; if unsure, call 311 or have a licensed plumber check the lines.
- If you want the storm route, verify all five conditions — no algaecides, one week held after the last chlorine dose, chlorine at or below 0.01 mg/L, sodium sulphite treatment, copper at or below 0.04 mg/L — and keep test and treatment records.
- If discharging on your lot, check the slope first: where the water flows, how close the fence is, how much the ground can absorb, and whether a ravine slope is nearby.
- Handle filter backwash separately: sanitary sewer or your own lot, never the street or a neighbour's lot; keep pool-cover rainwater away from ravine slopes too.
- If the home is rented or a pool company maintains it, put the draining method in writing when you engage them — the duty remains the owner's.
I am Ming Ren. With pool draining, the reliable sequence never changes: identify the pool, identify the pipes, then start the pump.
This article is general information, not legal advice. Your plumbing connections and pool type affect the answer; confirm with the City of Toronto at 311 or a licensed plumber before you drain.
Primary sources: Toronto Municipal Code Chapter 681, Sewers, ss.681-11T, 681-11U, 681-11V, 681-11W, 681-14.1; City of Toronto, “How to Drain a Pool, Hot Tub & Spa” (consulted November 2026).


