I am Ming Ren, a Broker with RE/MAX Realtron.
The plain conclusion first: a showing is not an inspection. You get roughly half an hour, and you will not find every problem in it — nor do you need to. Your one job on that visit is to decide whether this home is worth an offer, and whether that offer should carry an inspection condition. So when I walk buyers through a home, my order is fixed and I never start with the finishes: trace the water first, check the systems second, and look at surfaces last. Dated finishes can be fixed with money. Water and system problems follow you home and keep finding you after you move in.
1. Trace the water: where has this house been wet?
Water is the most expensive enemy a house has, and it has one convenient habit: it leaves marks. Walk room by room and look for these:
| Where | What to look for | What it tells you |
|---|---|---|
| Basement corners and the bottom of door frames | Trim (moulding) lifting or discoloured; press it lightly — does it feel soft? Any water line where the wall meets the floor | A wall base that has stayed damp, or water that came in before; the wall and floor behind it may already be damaged |
| Basement concrete walls | The direction of cracks — vertical, horizontal, stair-step — each noted, with the location marked in your photos | Fine vertical cracks are usually shrinkage in the concrete; horizontal and stair-step cracks deserve a closer look from an inspector and a structural engineer |
| Kitchen and bathrooms | Turn on taps: water pressure and how fast drains clear. Feel the cabinet floor under the sink — damp or soft? Walk the edges of the floor for soft spots | Slow leaks hide most often under cabinets and under flooring; brand-new tile on top does not stop them |
| Upstairs rooms | Stains on walls below windows and in ceiling corners; discoloured wood at the bottom of window frames | Usually the leftover record of window-seal or roof leaks — ask whether it happened and whether it was repaired |
One caution: a stain is not a verdict. Note the location and the size, and put it on the inspection list. An old, dry stain and an active leak are completely different costs, and you cannot tell them apart by eye in half an hour. That is the inspector's job.
2. Check the systems — and who actually owns each piece of equipment
Before you finish with surfaces, sort out what sits in the basement and inside the walls. This part has two halves: electrical is about safety; equipment is about ownership.
Electrical. Start at the panel: breakers or an old fuse box, and how many amps — write it down. In older homes, watch for two kinds of wiring. The first is knob-and-tube, common in homes from the early 1900s to the 1940s. Ontario's Electrical Safety Authority (ESA) position is that knob-and-tube properly maintained by a licensed electrical contractor can be safe, and the current code does not retroactively require its removal — but many insurers will not cover a home that has it, or require replacement first. The second is aluminum wiring, common from the mid-1960s to the late 1970s. The ESA position is that aluminum is safe when connections and terminations are done properly; its risk sits at the joints, where connections loosen and heat up — a switch or outlet plate that feels warm, discolouration, or flickering lights are the warning signs. At a showing, do not remove panel covers or open outlets. Do three things only: note it, photograph it, and leave it for the inspector and a licensed electrician.
Equipment ownership. Furnace, water heater, water softener, air conditioner — check the label on each one and ask one question: is this the seller's, or is it rented? In Ontario, a good deal of this equipment sits on rental contracts, and when the house sells, the contract transfers to the buyer, who takes over the monthly payments. An invented example, using illustrative numbers only: a rented water heater plus a rented softener at $65 a month combined (illustrative figure) is $780 a year; if years remain on those contracts, that belongs in your price calculation, not in your surprises after closing. At the attic hatch, one glance is enough: if you see loose, pebble-like grey-brown insulation, it may be vermiculite. Health Canada advises that some vermiculite sold before 1990 may contain asbestos, that the risk is very low while it stays sealed and undisturbed, and that the worst move is to disturb, sample or remove it yourself. Do not touch it at a showing. Note it, and let qualified professionals test and handle it.
3. Surfaces last — but look at what is behind them
Only now do we get to what most people look at first. For every surface item, I ask one question: is this "old," or is this "damaged"? Old is a negotiating point. Damaged has a cause you need to find.
- Windows: Fogging or white deposits between the two panes of a double-pane window means the seal has failed and the insulating value is largely gone. Open and close each window; check that the locks engage.
- Floors: Walk every room slowly and feel with your feet for soft spots — kitchen and bathroom doorways and the basement entrance are the usual places. On laminate and engineered floors, look for lifted edges and bubbled seams; tile that sounds hollow underfoot has lost its bond.
- Cracks: Hairline vertical cracks in drywall are usually just material shrinkage — do not scare yourself. Diagonal cracks at the corners of doors and windows, and any crack with visible offset, get photographed and left for the inspector to judge.
- Lights and outlets: Turn on every light; note any that are dead or flickering. Outlets near water — kitchen and bathroom counters — should be GFCI-protected. Note that too, and have it verified at the inspection.
By the end of this loop you should be holding one list of locations and photo numbers. It has two uses: it is the priority list you hand your home inspector, and it is the basis for your own math on the offer — what will certainly cost money, kept separate from what still needs checking.
Three misunderstandings I hear most often
"If I look carefully enough at the showing, I can skip the inspection condition." No. A showing is screening by eye. An inspector has moisture meters and thermal imaging and hours to work, and there are places you simply may not touch during a showing. Dropping the inspection condition does not save you time; it gives up the entire basis you would have had to negotiate with afterward.
"Knob-and-tube or aluminum wiring means I cannot buy this house." Also no. On the ESA's position, neither type is automatically unsafe — what matters is maintenance and proper connections. What actually stops people first is usually insurance. Before your offer goes firm, call your insurance broker and confirm whether this home can be insured and whether an electrical assessment is needed first. Do not find out after closing that the policy cannot be issued.
"The equipment is in the house, so it must be the seller's." No. Water heaters, softeners, furnaces and alarm systems can all be rented. If the listing says nothing, that does not mean there is no contract. Get the ownership of every piece of equipment confirmed by the seller in writing and written into the offer. A verbal "it's all ours" counts for nothing after closing.
At your next showing, do these six things in order
- Before you go in, walk around the outside: does the ground slope away from the house or toward it, where do the downspouts discharge, and are there cracks or water stains on the exposed foundation?
- Go to the basement first: corners, trim and crack directions, then photograph the labels on the panel, furnace, water heater and softener, one by one.
- In the kitchen and every bathroom, run the water, flush, feel the cabinet floors, and walk the floor edges.
- Open and close every window and check for fogging between the panes; turn on the lights in every room and note flickering or dead fixtures.
- Photograph every concern on the spot, with its location noted. That list is your inspector's priority list and the basis for your conditions and your price.
- The same day you get home, do two things: call your insurance broker about insuring an older home and its wiring, and have your agent obtain written confirmation from the seller of who owns each piece of equipment.
Trust Professional, Diligent Work. I am Ming Ren. When I walk through a home with buyers, I am not looking at how well it is dressed — I am looking at where it hides its problems. Take this list to your next showing and work through it, room by room.
This article is general information only. It is not a home inspection report and not legal or technical advice. A home's condition should be confirmed by licensed inspectors, electricians and other qualified professionals; equipment contracts and offer terms should be reviewed with your agent and lawyer before you offer.
Primary sources: Electrical Safety Authority (ESA) published guidance on knob-and-tube and aluminum wiring; Health Canada health advisory on vermiculite insulation that may contain asbestos (both consulted November 2026). The $65 monthly figure is illustrative only, not a real contract.
Frequently asked questions
If I look carefully enough at a showing, can I skip the inspection condition?
No. A showing is screening by eye, while an inspector has moisture meters, thermal imaging and hours to work, and there are places you may not touch during a showing. Dropping the condition gives up the entire basis you would have had to negotiate with afterward.
Does knob-and-tube or aluminum wiring mean I cannot buy the house?
No. On the ESA's position, neither type is automatically unsafe; what matters is maintenance and proper connections. What usually stops people first is insurance, so confirm insurability with your insurance broker before your offer goes firm.
If the equipment is in the house, is it automatically the seller's?
No. Water heaters, softeners, furnaces and alarm systems can all be rented. Get the ownership of every piece of equipment confirmed by the seller in writing and written into the offer.


