Ming RenBroker · RE/MAX Realtron Realty Inc., Brokerage
☎ 647-779-9186

Commercial Real Estate & Leasing

Adding a Drive-Through Window in Toronto? Measure the 30 Metres First, Then Count the Queue

By , Broker, RE/MAX Realtron Realty Inc. (About Ming) · Published

Ming Ren · Broker · RE/MAX Realtron Realty Inc., Brokerage

← All articles · Commercial Real Estate & Leasing · Category guide

I am Ming Ren, a Broker with RE/MAX Realtron.

The plain conclusion first: when a tenant wants to add a drive-through window to your unit, the construction is not the hard part — the zoning is. Section 150.80 of Toronto's Zoning By-law 569-2013 is devoted to drive through facilities, and it contains two tests that can kill the idea outright: whether the lot sits in a prohibited zone category, and whether the facility is at least 30 metres from residential-category lots. Fail either one and no window design will save the plan.

Test one: which zone is the lot in?

Chapter 800 defines a drive through facility as premises used to provide or dispense products or services, through an attendant, a window or an automated machine, to people who stay in their vehicles in a designated stacking aisle. It is not limited to fast food — a pharmacy pickup window or a coffee window in that form counts too.

Under s.150.80.20.1, a drive through facility is not permitted in the Residential, Residential Apartment or Commercial Residential Employment zone categories, and in a Commercial Residential (CR) zone only where the zone label carries an 'r' value of 0.0. One more rule is easy to miss: a drive-through must operate in combination with another use, neither of them ancillary to the other, and each use must satisfy its own regulations.

Test two: the 30-metre separation, queue included

Section 150.80.40.1 requires a drive through facility, including its stacking aisles, to be at least 30.0 metres from any lot in those residential zone categories.

Read that carefully in two ways. First, the measurement covers the whole facility — the queue of waiting cars is part of it, so a lane wrapped around the back of the building toward a residential lot fails just as a window would. Second, the test looks at the zoning category of the neighbouring lot, not at what happens to sit on it today: a vacant or commercially used lot that is zoned in a residential category still counts.

There is also a placement rule for the lane itself: a stacking aisle generally may not sit in a front yard or a street-facing side yard, subject to limited exceptions such as certain employment-zone lots. The "loop it along the street" sketch fails on most retail sites.

Test three: count the stacking spaces — 10 with food or beverage, 4 without

Only after the separation works do you count cars. Section 150.80.20.1 sets the numbers:

Item Requirement
Size of each stacking space At least 3.0 m wide by 6.5 m long
Combined with a use selling food or beverage At least 10 stacking spaces
Combined with any other use At least 4 stacking spaces
Separation from residential-category lots At least 30.0 m, facility and aisle included

Take that table to your parking lot. Ten cars in a line, turning room, and a queue that must not block other tenants' spaces or fire routes — on an older plaza's small lot, this is usually where the plan dies.

Three common misunderstandings

1. "It is just a small window in the wall — a renovation, not a new use." In zoning terms a drive-through is a defined use with its own section of the by-law. It is not treated as a minor alteration.

2. "The lot next door is not residential right now, so the 30 metres does not apply." The separation is measured against the lot's zone category, not its current use. A residentially zoned lot counts even if nothing residential stands on it today.

3. "Close enough on the stacking spaces should be fine." Ten and four are minimums written in the by-law, and 3.0 m by 6.5 m is a hard dimension. Falling short means a minor variance or a zoning amendment — a separate process, timeline and cost that cannot be assumed.

My checklist before you sign

  1. Confirm the lot's zone label and pull the zone categories of the surrounding lots; make sure the site is not in a prohibited category.
  2. Measure on a site plan: facility plus aisle to the nearest residential-category lot line — is it a full 30.0 metres?
  3. Classify the tenant's use: 10 stacking spaces with food or beverage, 4 otherwise, each 3.0 m by 6.5 m, drawn in full on the plan without blocking other spaces or routes.
  4. Check for site-specific exceptions or an existing site plan approval for the address — an old approval may help, or may restrict you.
  5. Write the division of labour into the lease: who applies, who pays for the lane work, and what happens if the standard cannot be met.

Honest in conduct, diligent in work — that is how I run my practice. I am Ming Ren. Before a tenant's sketch turns into a lease, send me the address and we will measure the zoning and the 30 metres first.


This article is general information, not legal advice. Drive-through permission turns on the City of Toronto's current zoning text and the review of the specific lot; confirm with the City and an Ontario lawyer before signing.

Primary sources: City of Toronto Zoning By-law 569-2013, s.150.80 (ss.150.80.20.1, 150.80.40.1) and Chapter 800 definitions of drive through facility and stacking aisle (City of Toronto office consolidation, checked November 2026).

This article in other languages: 中文فارسی

Want to talk about your home?

You can also call directly, or scan the code to add Ming on WeChat.

Ming’s WeChat QR code
Scan to add on WeChat

Community guides by city

All cities →
☎ Call MingFree Evaluation