I am Ming Ren, a Broker with RE/MAX Realtron.
The plain conclusion first: if you want to carve a bedroom out of a basement and rent it, do not start with finishes — start by measuring the window. Ontario's Building Code sets four hard numbers for a bedroom egress window, and missing any one of them means the room does not qualify as a compliant bedroom. The windows in older basements are usually small and high, and in my experience most of them fail. That is not a scare tactic; it is what I keep running into on showings.
What the Code actually requires
The rule is Article 9.9.10.1, "Egress Windows or Doors for Bedrooms," in Division B, Part 9 of the Ontario Building Code (O. Reg. 163/24). Its logic runs like this:
Every floor level that contains a bedroom must have at least one outside window that meets the requirements — unless a door on that same floor level provides direct access to the exterior. Note what the rule attaches to: the floor level containing a bedroom, and a basement level counts. The reason is simple. In a basement fire, the stairs are the first thing smoke blocks, and this window is the second way out for the occupant and the way in for firefighters. It is a safety floor, not a finishing choice.
The window itself also has to behave properly: it must be openable from the inside without tools, it must hold the required opening on its own without additional support, and if it is a sliding window, the dimensions are measured on the openable portion only — not on the whole window.
The four numbers, measured one by one
| Requirement | Code minimum/maximum | Source |
|---|---|---|
| Unobstructed openable area | At least 0.35 m² | 9.9.10.1(1)(b) |
| Smallest dimension of the opening | No dimension less than 380 mm | 9.9.10.1(1)(b) |
| Sill height | Maximum 1,000 mm above the floor — except basement areas | 9.9.10.1(2) |
| Window-well clearance | At least 550 mm in front of the window, where the window opens into a well | 9.9.10.1(5) |
The area rule and the minimum-dimension rule apply at the same time, and that is where most windows fail. An invented example, purely to show the arithmetic: an opening of 1,000 mm × 350 mm gives you exactly 0.35 m², which looks like a pass — but the short side is 350 mm, under the 380 mm minimum, so it does not comply. If a person cannot fit through it, the area figure does not save it.
The sill-height rule carries a key exception for basements: Sentence 9.9.10.1(2) sets the 1,000 mm maximum sill height "except for basement areas." So a higher basement sill is not, by itself, a failure under this Article. Do not read that as "anything goes in a basement" — the 0.35 m² area and the 380 mm minimum dimension apply in the basement exactly as written, with no discount.
Two companion rules govern the window well. If the sash swings toward the well, its operation must not reduce the clearance in a way that would restrict escape. And if a protective enclosure is installed over the well, it must be openable from the inside without keys, tools or special knowledge. A perfectly sized well with a cover that cannot be opened from inside is a locked exit.
One more word on how to measure, because this is where most people go wrong at step one: open the window fully and measure the inside length and width of the opening a person can actually pass through — do not let the tape rest on the frame or the hardware. A quick sanity check: a 380 mm × 380 mm opening is only about 0.14 m², nowhere near 0.35 m². So do not assume that passing the minimum dimension means passing the area; the two numbers police different things and each has to be checked on its own. A casement window that swings fully open will usually deliver the required openable area more easily than a slider, which is worth calculating before you replace a basement window.
A passing window does not make a legal basement
I want to be clear about this: the egress window is one item on a longer list, not the whole list. Turning a basement into a rentable living unit also runs into ceiling height, light and ventilation, smoke and carbon monoxide alarms, fire separation, electrical work, and your municipality's own second-unit registration rules. Each of those has its own provisions and standards, and each has to be checked on its own.
Also, cutting in a compliant egress window is rarely just a window swap. It usually means digging or widening a window well and cutting the foundation wall — structural work that calls for a building permit, qualified people doing the work, and a municipal inspection at the end. An unpermitted conversion becomes a problem at every later step: when you rent, when you insure, and when you have to disclose on a sale. Buyers should apply the same thinking in reverse: if a seller tells you the basement bedroom is "legal," do not nod along — ask to see the permit and inspection records.
One practical word on timing: run the numbers on this window before you buy or before you build, not after a tenant has moved in. Ten minutes on a showing with a tape measure, plus a look into the window well, will tell you most of what you need to know about whether that "basement bedroom" truly complies or merely looks like a bedroom. The first kind earns lawful rent and can be described honestly in a listing; the second kind carries risk with every rent cheque and invites hard questions after any incident. The difference between the two is exactly these four numbers.
Three misunderstandings I hear most often
"Just measure the glass." No. The Code measures the unobstructed open portion with the window fully open — not the glass area, not the rough opening in the wall, not the frame. A sliding window that only opens halfway is measured on the half that opens.
"The basement sill is over a metre high, so the room can't comply." Not necessarily. The 1,000 mm sill maximum expressly does not apply to basement areas. The numbers a basement cannot escape are the 0.35 m² opening and the 380 mm minimum dimension.
"Every bedroom needs its own egress window." The Article is written per floor level: at least one qualifying window on a level that contains a bedroom. An extra compliant window is never a bad idea for safety, but when you are judging whether an existing house complies, start from what the Code actually says — do not add to it, and do not subtract from it.
If you are planning a basement rental bedroom, do these five things in order
- Measure the existing window first: fully open, measure the length and width of the unobstructed open portion, multiply for the area, and check the short side against 380 mm. Run all four numbers before you spend a dollar.
- Check the window well: is there at least 550 mm of clearance in front of the window, does the sash eat into that clearance when it swings, and can any cover over the well be opened from inside by hand?
- If there is a door on the same level leading directly outside, confirm whether it actually fits the door exception in the Article. If you are not sure, treat it as if it does not, and plan to the window standard.
- If work is needed, ask your municipal building department about the permit process first, then have a qualified designer or contractor prepare the plan. Do not cut the foundation wall first and chase paperwork later.
- Keep the full paper trail when the work is done: permit, drawings, inspection records. When you sign a lease, renew insurance, or sell one day, that file is the only proof behind the words "legal bedroom."
Trust Professional, Diligent Work. I am Ming Ren. If you are dealing with a basement rental or a second-unit compliance question, measure the window, gather the documents, and we will go through the Code item by item.
This article is general information only, not legal advice and not a building design opinion. Your property's specifics and your municipality's registration rules can change the conclusion. Confirm with your municipal building department or a qualified designer before starting work.
Primary source: Ontario Building Code, O. Reg. 163/24, Division B, Part 9, Article 9.9.10.1 (Ontario e-Laws / Building Code Compendium, consulted November 2026). The 1,000 mm × 350 mm figures are illustrative only, not a real case.
Frequently asked questions
Can I just measure the glass?
No. The Code measures the unobstructed open portion with the window fully open — not the glass area, not the rough opening, not the frame. A sliding window that only opens halfway is measured on the half that opens.
The basement sill is over a metre high, so the room can't comply?
Not necessarily. The 1,000 mm sill maximum expressly does not apply to basement areas. The numbers a basement cannot escape are the 0.35 m² opening and the 380 mm minimum dimension.
Does every bedroom need its own egress window?
The Article is written per floor level: at least one qualifying window on a level that contains a bedroom. When judging whether an existing house complies, start from what the Code actually says.


